Atlas ProJack 35 3,500 lb Sliding Rolling Bridge Jack

Add-on rolling bridge jack for the Atlas Garage PRO8000, PRO8000EXT, and PRO9000 8k–9k 4-post lifts.

3,500 lb Sliding Rolling Bridge Jack for Hobbyist 4-Post Lift Bays

A 4-post lift parks the vehicle by its tires. Anything that requires removing the wheels — brake rotors, tires, wheel bearings, shocks — means you need a jack that lives on the lift itself. The ProJack 35 is the matched sliding bridge jack for the Atlas Garage PRO line of 4-post lifts.

The ProJack 35 is a 3,500 lb capacity manual hydraulic sliding bridge jack that drops onto the runways of a hobbyist 4-post lift and lifts the vehicle off the runway at any point along the lift’s length. Scissor mechanism for level lifting, multiple safety lock positions, and a 4-piece truck adapter set included — no shop air required, hand-pump operation.

What’s Included

• Atlas ProJack 35 sliding bridge jack with hand pump
• 4-piece truck adapter set (2 each at 1-1/2″ and 5″)
• Scissor lifting mechanism with multiple safety lock positions
• Sliding bridge with adjustable arms

Made For

Built for hobbyist 4-post lift owners who want wheels-free service in their garage without running shop air to the lift.

• Home garages with an Atlas Garage PRO8000, PRO8000EXT, or PRO9000
• Small shops without compressed air at every lift
• Compatible with APEX8, APEX9, 408SL, 409HP 4-post lifts
• Enthusiasts doing their own brake, tire and suspension work
• Storage bays where the lift doubles as a service platform

Features

• 3,500 lb Capacity — Lifts the front or rear axle of vehicles up to roughly 7,000 lb gross.
• Manual Hydraulic Hand Pump — No shop air required. Hand-pump operation makes this the right jack for garages without compressed air at the lift.
• Sliding Bridge Design — The bridge slides along the runways to any working position.
• 20-1/2″ to 47″ Lower Extension Width — Fits the runway gap on most hobbyist 4-post lifts.
• 39-1/2″ to 64-3/4″ Top Width — The lifting pads themselves adjust to span both narrow sedans and full-size trucks.
• Scissor Mechanism for Level Lifting — Keeps the lifting pads level throughout travel.
• Multiple Safety Lock Positions — Mechanical safety locks engage at multiple heights.
• 4-Piece Truck Adapter Set Included — Two 1-1/2″ and two 5″ adapters in the box.
• 17-1/4″ Max Lift Height with Adapters — Enough working clearance for wheel removal and brake service.

A Hand Pump Instead of an Air Line

Most rolling bridge jacks run air-over-hydraulic, which assumes there is a compressor plumbed to the lift. In a home garage that is often not the case, and running a line to the far end of the bay for one jack is a job in itself.

The ProJack 35 pumps by hand. The hydraulics are the same scissor arrangement, but the power comes from the handle rather than from 100 psi of shop air, so the jack works the day it is bolted together with nothing else installed.

The trade is a few more strokes on the handle in exchange for a jack that has no air requirement at all — which for a 3,500 lb axle lift on a hobbyist lift is a fair swap.

Sized to the Runway Gap and the Vehicle

Two widths matter on a bridge jack, and this one adjusts both. The lower extension spans 20-1/2″ to 47″ to sit across the runway gap, and the top arms span 39-1/2″ to 64-3/4″ to reach the factory lift points on anything from a narrow sedan to a full-size truck.

Pad height starts at 3-1/2″ above the runway and reaches 11″ on its own, or 17-1/4″ with the supplied adapters stacked — two at 1-1/2″ and two at 5″, on a 1-1/2″ peg. That range covers wheel removal on a low car and frame contact on a pickup without hunting for blocks.

The scissor mechanism keeps both pads level through the whole travel, and the mechanical locks engage at multiple heights so the load sits on steel rather than on hydraulic pressure while the wheel is off.

The Right Rolling Bridge Jack for Your Lift

For wheels-free work on an Atlas Garage PRO 4-post lift in a garage with no air at the lift, the ProJack 35 is the jack: 3,500 lb capacity, hand-pump hydraulics, and a 4-piece adapter set in the box.

Don’t wait — scroll back up and click the orange Add to Cart button to get this rolling bridge jack on its way to your shop.

Specs

Technical Specifications